Photos from current listings. Actual item, color, and included accessories may vary.
Bearing Puller Buying Guide
Bearing pullers separate press-fit bearings, races, and hubs using mechanical screw force or hydraulic pressure, and the core trade-off is jaw reach versus tonnage: manual 2/3-jaw sets suit light automotive and shop work, while hydraulic and vehicle-specific kits handle seized, high-preload assemblies. Buy a set only when its jaw spread, reach, and tonnage cover your largest bearing; step to a hydraulic or dedicated axle kit for Class 6-8 or Dana/Ford 9-inch service.
At a glance
- Category
- Hand Tools
- Data updated
- Nov 20, 2026
Current offers
Bearing Puller Three-Jaw Inner fit for Automotive Motorcycle Mechanical Bearings$42.99
View on Mallflare
36-in-1 Bearing Puller Set, 36 PCS 3-Jaw Hook For Internal External Bearings And Without Inner Shaft, Multifunctional Removal Tool With Heavy Duty Portable Storage Case$52.99
View on Mallflare
9* Inner Bearing Puller Set Remover Slide Hammer Internal Kit 8-32mm Blind Hole$77.99
View on Mallflare
15 Ton Hydraulic Gear/Bearing/Wheel Bearing Puller Separator 2 Or 3 Jaws W/ Case$95.99
View on Mallflare
Hub Bearing Puller fit for Rear Axle Drive Removal Tool Universal fit for Class 6-8$109.99
View on Mallflare
Rear Wheel Axle Bearing Puller & Tone Ring Tool Fit For TOYOTA T100 1995-1998 TACOMA$111.99
View on Mallflare
Commercial Bearing Puller fit for Dana 30 40 60 70 Ford 9inch Service Tool Steel$211.99
View on Mallflare
Gear Puller Set, 3 In/4 In/6 In/8 In 3 Jaw Bearing With Reversible Jaws, 2 Jaw/3 Jaw Pulley Tool, 4 PCS Heavy Duty Kit For Flywheel Removal$39.99
View on Mallflare
Hydraulic Gear Puller, 5 Ton Max Capacity Wheel Bearing Pulling Separator, 2 Or 3 Jaws Vertically And Horizontally, 8" Jaw With Case For Hubs$63.99
View on Mallflare
Wheel Bearing Press Kit, 23 PCS FWD Puller Tools, For Front Drive Removal And Installation, Tool With Sliding Screw, Bushings, Sleeve Plates, Storage Case$69.99
View on Mallflare
Jaw Gear Bearing Flywheel Pulley Removal Tool, 2 Or 3 Reversible Jaws Wheel Puller, Vertically And Horizontally, External And Internal, 2-Piece$74.99
View on Mallflare
Hydraulic Gear Puller, 15 Ton Max Capacity Wheel Bearing Pulling Separator, 2 Or 3 Jaws Vertically And Horizontally, 12" Jaw With Case For Hubs$101.99
View on Mallflare
Bearing Press Kit, 10+24 Pcs, 2 In 1 Ball Joint & Wheel Puller Kit, Race And Seal Driver Set With 13 Bushings, C-Frame And Sleeves, Heavy Duty Removal Installation Set Case$119.99
View on Mallflare
Slide Hammer Dent Puller Auto Body Repair Bearing Removal Tool Kit Axle Hub$119.99
View on Mallflare
18pc Slide Hammer Dent Puller Auto Body Repair Bearing Axel Kits$161.99
View on Mallflare
Highlights
- Manual 3-jaw pullers transmit force through a central screw; hydraulic units convert pump pressure into 5-15 ton separation force for seized bearings.
- Reversible 2-jaw/3-jaw jaws grip inner races from inside or outer races from outside; jaw spread and reach, not piece count, set the working range.
- Dedicated axle and hub kits use vehicle-specific adapters (Dana 30/40/60/70, Ford 9-inch, Toyota T100/Tacoma) instead of universal jaws.
- Steel jaws and forged yokes hold rated tonnage; plastic and stamped components belong to light-duty internal-blind-bearing hooks only.
Best use cases
- Pick a 3-jaw manual set with 3/4/6/8-inch reversible jaws for pressed alternator, pulley, and small motor bearings; skip hydraulic for anything under roughly 1 ton of required force.
- Choose a 5-15 ton hydraulic 2/3-jaw separator for seized wheel hubs and large gear bearings; a manual screw puller will flex or strip under that load.
- Use a vehicle-specific hub/axle kit (Dana, Ford 9-inch, Toyota) for driveline service; universal jaw sets cannot safely seat on tone rings and axle flanges.
- Buy a blind-hole/internal puller with hook jaws for bearings recessed in housings; external 2-jaw pullers cannot reach a race with no exposed outer edge.
Buying tips
- Match jaw reach to the deepest recess: a 4-inch reach puller will not extract a bearing set 6 inches inside a housing bore.
- Size tonnage to the fit: manual screw pullers suit light press fits, while 5-ton hydraulic and above is required for corroded hub and axle bearings.
- Confirm jaw spread exceeds the outer race diameter by a margin; jaws that barely span the bearing slip off under load.
- For blind bearings, buy hook-style internal jaws with a slide-hammer or threaded puller body; standard external jaws cannot grip an inner race.
Specs
| Pull Type | Manual screw vs hydraulic ram |
|---|---|
| Jaw Configuration | 2-jaw / 3-jaw reversible |
| Capacity | Manual light-duty to 15-ton hydraulic |
| Jaw Reach | 3 in to 8 in spread/reach |
Related searches
What to check before buying
- Measure the bearing outer diameter and recess depth; jaw spread must exceed OD and reach must exceed depth.
- Identify whether the bearing is exposed externally or recessed internally to choose external 2/3-jaw versus internal hook jaws.
- Check vehicle axle standard (Dana, Ford 9-inch, Toyota) before buying a dedicated hub kit; universal kits do not fit these flanges.
- Confirm the puller body clears surrounding brake, suspension, or housing metal through the full screw or hydraulic ram travel.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 20, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.