DIY Tool Picks

Westward Dial Indicator Buying Guide

A Westward Dial Indicator is a precision measuring instrument used to check small linear deviations, runout, and alignment in machining and inspection work. The primary trade-off is between measuring resolution/accuracy and the robustness of the movement and mounting interface. Buy a calibrated, jeweled-bearing model with a clear graduations-to-range match for your tolerance, and skip uncalibrated or oversize-range units if you need sub-thousandth inspection.

Graduation:0.001 in / 0.0005 in / 0.01 mmMeasuring Range:0.100 in / 0.250 in / 0.500 inDial Face Size:AGD Group 2: 2 in diameterMounting Stem:3/8 in (9.5 mm) or 8 mm

At a glance

Price range
Price range not synced yet
Category
Measuring & Layout Tools
Data updated
Nov 21, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Westward dial indicators use a rack-and-pinion movement with jeweled bearings; AGD Group 2 is the common 2-inch-diameter face standard for general shop use.
  • Graduation vs range is fixed: 0.001-inch graduations pair with 0.250- or 0.500-inch range; 0.0005-inch graduations are reserved for 0.100-inch or shorter range.
  • Accuracy is specified as total error over the full range plus hysteresis; a typical ±0.001-inch full-range tolerance applies to 0.001-inch-graduation models.
  • Mounting stems follow the 3/8-inch (9.5 mm) or 8 mm lug-back standard; choose the stem diameter and back type that match your magnetic base or indicator stand.

Best use cases

  • Best fit: checking spindle runout, shaft eccentricity, or lathe chuck alignment — pick a 0.0005-inch graduation, 0.100-inch range model for the tightest tolerance.
  • Best fit: general machine setup and tramming — a 0.001-inch graduation, 0.250- or 0.500-inch range indicator with a lug back covers most vise and fixture work.
  • Wrong fit: measuring large linear travel or bore diameters — a dial indicator's short range makes it the wrong tool; use a dial caliper or bore gauge instead.
  • Wrong fit: dirty foundry or heavy coolant environments — unprotected rack mechanisms can jam; choose a sealed or dust-protected indicator if coolant and chips are present.

Buying tips

  • Match graduation to tolerance first: 0.001-inch for general machining, 0.0005-inch only when your print tolerance is tighter than ±0.001 inch.
  • Range should exceed the expected deviation by at least 50% so the plunger never bottoms out during sweep or tramming.
  • Confirm the mounting interface before buying: 3/8-inch stem with lug back is the most common for magnetic-base use; 8 mm stems need metric holders.
  • Prefer a continuous dial with a revolution counter for 0.100-inch or longer ranges; without a counter you can lose track of full revolutions on 0.500-inch models.

Specs

Graduation0.001 in / 0.0005 in / 0.01 mm
Measuring Range0.100 in / 0.250 in / 0.500 in
Dial Face SizeAGD Group 2: 2 in diameter
Mounting Stem3/8 in (9.5 mm) or 8 mm

Related searches

What to check before buying

  • Measure your indicator stand or magnetic base clamp opening to confirm it accepts a 3/8-inch (9.5 mm) or 8 mm stem.
  • Check that the lug back or back-plate style (flat back, lug back, or rear stem) matches your holder's mounting hole pattern.
  • Verify shop temperature is stable near 68°F (20°C); thermal expansion of the workpiece and indicator affects sub-thousandth readings.
  • Have a known reference (gauge block or calibrated ring) on hand to zero-check the indicator before relying on absolute readings.

FAQ

All Measuring & Layout Tools buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 21, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.