DIY Tool Picks

Photos from current listings. Actual item, color, and included accessories may vary.

Spray Gun Buying Guide

A spray gun is a paint delivery tool whose core trade-off is atomization quality and material compatibility versus overspray, thinning requirements, and air-source dependency. HVLP (high volume, low pressure) and LVLP guns give fine automotive-grade finishes but need a compressor and reduce overspray; airless and cordless electric units move thick coatings fast but produce coarser finishes and demand tip or viscosity matching. Choose HP/LVLP with a real compressor for cars and cabinets; choose airless for fences, walls, and large exterior areas; choose cordless handheld only for small touch-up and thin stains.

Gun Type:HVLP / LVLP / Airless / CordlessNozzle Size:1.3-2.0 mm (material-dependent)Air Demand:4-15 CFM at 40-90 PSICup / Hopper:600-1000 ml cup; 1.4-2 gal hopper
Typical price range$19.99 – $189.99

At a glance

Category
Painting & Finishing Supplies
Data updated
Nov 20, 2026

Current offers

Highlights

  • HVLP/LVLP guns atomize at 4-10 PSI at the cap, delivering 65-80% transfer efficiency and far less overspray than conventional high-pressure guns, but require a compressor with 4-15 CFM at 40-90 PSI depending on nozzle size.
  • Airless sprayers run 2,000-3,600 PSI fluid pressure; tip orifice size controls finish and material — 0.009-0.013 in for lacquer and stain, 0.015-0.019 in for latex and exterior walls.
  • Nozzle and needle sets are the primary wear part: 1.3 mm suits automotive basecoat/clearcoat and cabinet lacquer; 1.4-1.5 mm suits primer and heavier enamels; 1.7-2.0 mm handles high-viscosity latex and texture coats.
  • Cordless handheld sprayers typically atomize 800-1000 ml cups of thinned material using 18-20 V battery platforms and produce a coarser finish than HVLP; they are touch-up tools, not finish-grade guns.

Best use cases

  • Automotive panels and cabinet doors: pick an HVLP or LVLP gravity-feed gun with 1.3 mm nozzle, a regulator at the gun, and a compressor delivering at least 10 CFM at 40 PSI — skip cordless and airless entirely.
  • Interior walls, fences, and exterior siding: pick an airless sprayer with a 0.015-0.019 in reversible tip and a 50 ft hose — skip HVLP, which cannot atomize unthinned latex efficiently.
  • Drywall texture, popcorn, knockdown, and stucco: pick a hopper gun with interchangeable 3.5/6/8 mm nozzles or a dedicated texture/plaster hopper — skip fine-finish gravity guns, which clog on heavy material.
  • Small touch-up, furniture refresh, and thin stains: a cordless 18-20 V handheld with a 800-1000 ml cup is adequate — skip it for any full panel or finish-critical work.

Buying tips

  • Match nozzle to material: 1.3 mm for basecoat/clearcoat and lacquer, 1.4-1.5 mm for primer and enamel, 1.7-2.0 mm for latex and primer-filler; a gun without a spare nozzle set limits you to one coating class.
  • Size the compressor to the gun: HVLP typically needs 4-15 CFM at 40-90 PSI; confirm CFM at working pressure, not tank size, or atomization will collapse mid-panel.
  • For airless, buy a unit rated at least 300-500 PSI above the tip's maximum rating and choose a reversible tip so you can clear clogs without disassembly.
  • Cordless sprayers are platform-locked: buy the bare tool only if you already own that battery system; a 1000 ml cup at high viscosity drains fast and requires thinning.

Specs

Gun TypeHVLP / LVLP / Airless / Cordless
Nozzle Size1.3-2.0 mm (material-dependent)
Air Demand4-15 CFM at 40-90 PSI
Cup / Hopper600-1000 ml cup; 1.4-2 gal hopper

Related searches

What to check before buying

  • Measure the compressor's CFM at 40 PSI and confirm it meets the gun's requirement before buying any HVLP or LVLP unit.
  • Check coating viscosity and thinning ratio — most HVLP and cordless guns require 10-30% thinning for latex; airless handles unthinned material.
  • Confirm cup or hopper capacity against job size: 600-1000 ml for panels and doors, 1.4-2 gal hopper for texture and stucco.
  • Verify air fittings and hose: 1/4 in NPT is standard in the US; European guns may use 1/4 in BSP, requiring an adapter.

FAQ

All Painting & Finishing Supplies buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 20, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.