Photos from current listings. Actual item, color, and included accessories may vary.
Electric Submersible Pump Buying Guide
An electric submersible pump is a sealed motor-and-impeller unit that pushes water upward from a well, cistern, or sump while fully submerged. The core trade-off is head-versus-flow: higher total dynamic head (lift + pipe friction) forces you into higher horsepower, larger-diameter impeller stacks, and 230V power. Buy a stainless-steel-bodied unit with a rated head curve above your measured vertical lift plus 10-20% friction margin, and skip any pump whose advertised head assumes zero pipe loss.
At a glance
- Category
- Plumbing Tools
- Data updated
- Nov 20, 2026
Current offers
Deep Well Submersible Pump, 0.5HP 230V/60Hz, 28gpm 167ft Head, With 33ft Electric Cord, 4" Stainless Steel Water Pumps For Industrial, Irrigation And Home Use, IP68 Waterproof Grade$140.99
View on Mallflare
Deep Well Submersible Pump, 0.5HP 115V/60Hz, 28gpm Flow 167ft Head, With 33ft Electric Cord, 4" Stainless Steel Water Pumps For Industrial, Irrigation&Home Use, IP68 Waterproof Grade$144.99
View on Mallflare
Deep Well Submersible Pump, 1.5HP 230V/60Hz, 37gpm 276ft Head, With 33ft Electric Cord, 4' Stainless Steel Water Pumps For Industrial, Irrigation And Home Use, IP68 Waterproof Grade$182.99
View on Mallflare
Deep Well Submersible Pump, 37GPM Flow 427 Ft Head, With 33 Ft Electric Cord, 4 Inch Stainless Steel Water Pumps For Industrial, Irrigation & Home Use, IP68 Waterproof Grade$200.99
View on Mallflare
Deep Well Submersible Pump, 3HP/2200W 230V/60Hz, 37GPM Flow 640 Ft Head, With 33 Ft Electric Cord, 4 Inch Stainless Steel Water Pumps For Industrial, Irrigation & Home Use, IP68 Waterproof Grade$268.99
View on Mallflare
Highlights
- 4-inch stainless-steel deep-well pumps are the standard borehole format; 230V/60Hz models dominate above 0.5HP because 115V circuits cap out around 1HP on a 15A breaker.
- Head ratings are maximum shut-off figures: a 167ft-head 0.5HP unit delivers roughly 28GPM only at low lift and near-zero flow at full head, so size from the published curve, not the headline number.
- Deeper lifts demand multi-stage impeller stacks: 0.5HP covers ~167ft, 1.5HP ~276ft, and 3HP/2200W reaches ~640ft head at reduced flow, so horsepower tiers map directly to well depth.
- IP68 sealing and built-in 33ft power cords are the baseline; check that the cord length exceeds your static water depth plus above-ground run, since splicing submersible cable degrades the waterproof rating.
Best use cases
- Best fit for a 4-inch borehole 100-250ft deep with household demand: choose the 1.5HP 230V/60Hz, 37GPM, 276ft-head unit; skip 0.5HP if your lift exceeds ~120ft.
- Best fit for shallow wells, cisterns, or irrigation under 100ft with only 115V available: the 0.5HP 115V/60Hz, 28GPM, 167ft-head model; skip it for deep static levels or long horizontal runs.
- Best fit for high-head or deep commercial/irrigation wells past 400ft: the 3HP/2200W 230V unit rated to 640ft head; skip 115V entirely and skip 1.5HP if lift plus friction exceeds ~250ft.
Buying tips
- Measure static water level, drawdown, and vertical lift, then add 2-3ft of friction loss per 100ft of pipe plus 1ft per 10ft of horizontal run; buy a pump whose rated head at your target flow exceeds that total.
- Match voltage to your circuit: 115V/60Hz tops out near 1HP on a 15A breaker; 1.5HP and 3HP units require 230V/60Hz dedicated circuits sized to the motor's full-load amps.
- Choose stainless-steel casing and impellers over thermoplastic for sand-prone or iron-rich water; confirm pump OD clears your borehole by at least 0.25 inch (4-inch pump in a 4.5-inch or larger well).
- Verify cord length covers static depth plus above-ground run and that the control box or capacitor start matches the motor; 3-wire plus ground motors need a starter box, 2-wire units have it integrated.
Specs
| Pump Diameter | 4 in stainless (needs 4.5 in+ bore) |
|---|---|
| Voltage / Frequency | 115V or 230V, 60Hz |
| Head vs Flow | 167-640 ft shut-off; 28-37 GPM peak |
| Sealing & Cord | IP68; 33 ft submersible cable |
Related searches
What to check before buying
- Know your well casing inner diameter: a 4-inch pump needs a 4.5-inch or larger borehole with at least 0.25 inch clearance.
- Measure total vertical lift from static water level to discharge point plus horizontal run and fitting count for friction-loss math.
- Confirm a dedicated 230V/60Hz circuit with breaker and wire gauge matched to motor full-load amps for 1.5HP and 3HP units.
- Check that the included power cord exceeds static depth plus above-ground distance, and plan a torque arrestor and safety rope for deep sets.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 20, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.