Photos from current listings. Actual item, color, and included accessories may vary.
Electric Well Pump Buying Guide
Electric well pumps are the motorized heart of a private water system, split into shallow-well jet pumps (suction up to about 25 ft) and deep-well submersible pumps (push water from 100–600+ ft). The core trade-off is between head capacity, flow rate, and electrical service: higher horsepower delivers more lift but demands 230V circuits, deeper drop pipe, and heavier-gauge cable. The dividing line is simple: if your static water level stays above 25 ft, a jet pump is the durable, serviceable choice; if the water table sits lower, only a submersible rated for your total dynamic head will last.
At a glance
- Category
- Plumbing Tools
- Data updated
- Nov 20, 2026
Current offers
Deep Well Submersible Pump, 0.5HP 230V/60Hz, 28gpm 167ft Head, With 33ft Electric Cord, 4" Stainless Steel Water Pumps For Industrial, Irrigation And Home Use, IP68 Waterproof Grade$140.99
View on Mallflare
Deep Well Submersible Pump, 0.5HP 115V/60Hz, 28gpm Flow 167ft Head, With 33ft Electric Cord, 4" Stainless Steel Water Pumps For Industrial, Irrigation&Home Use, IP68 Waterproof Grade$144.99
View on Mallflare
Deep Well Submersible Pump, 1HP 115V/60Hz, 37gpm Flow 207ft Head, With 33ft Electric Cord, 4" Stainless Steel Water For Industrial, Irrigation&Home Use, IP68 Waterproof Grade$145.99
View on Mallflare
Deep Well Submersible Pump, 1HP 230V/60Hz, 37gpm Flow 207ft Head, With 33ft Electric Cord, 4" Stainless Steel Water For Industrial, Irrigation&Home Use, IP68 Waterproof Grade$163.99
View on Mallflare
Deep Well Submersible Pump, 1.5HP 230V/60Hz, 37gpm 276ft Head, With 33ft Electric Cord, 4' Stainless Steel Water Pumps For Industrial, Irrigation And Home Use, IP68 Waterproof Grade$182.99
View on Mallflare
Deep Well Submersible Pump, 37GPM Flow 427 Ft Head, With 33 Ft Electric Cord, 4 Inch Stainless Steel Water Pumps For Industrial, Irrigation & Home Use, IP68 Waterproof Grade$200.99
View on Mallflare
Deep Well Submersible Pump, 3HP/2200W 230V/60Hz, 37GPM Flow 640 Ft Head, With 33 Ft Electric Cord, 4 Inch Stainless Steel Water Pumps For Industrial, Irrigation & Home Use, IP68 Waterproof Grade$268.99
View on Mallflare
Highlights
- Submersible pumps are rated by head (ft) and flow (GPM) together—a 0.5HP unit typically delivers ~28 GPM at 167 ft, while 3HP reaches ~640 ft, so match the curve, not just horsepower.
- Voltage tier matters: 115V/60Hz models are limited to roughly 1HP for shallow lifts, while 230V/60Hz single-phase is the standard for 1.5–3HP deep-well service.
- 4-inch stainless-steel bodies fit standard 4-inch ID well casings; build quality hinges on stainless grade (304 vs 316), motor winding insulation, and IP68 sealing.
- Total dynamic head = vertical lift + drawdown + friction losses + pressure-tank precharge; pumps should be selected at the midpoint of their curve, not maximum shutoff head.
Best use cases
- Choose a 0.5–1HP 115V submersible for shallow-to-mid wells (under 150 ft) on a dedicated 20A circuit—skip 230V models if no 240V service reaches the wellhead.
- Choose a 1.5–3HP 230V submersible for deep wells (200–600 ft) or high-demand irrigation and multi-fixture homes—skip 115V units, which overheat when pushed beyond their lift rating.
- Choose a shallow-well jet pump (not submersible) only when the water level stays above ~25 ft and you want above-ground serviceability—skip it for any deep or fluctuating water table.
- For livestock or irrigation with long runs, size up one head tier to cover friction loss—wrong-fit is buying by tank pressure alone without totaling pipe friction and elevation.
Buying tips
- Compute total dynamic head first: static water level + drawdown + elevation rise + friction (about 1 ft per 10 ft of 1-inch pipe). Select a pump whose rated head exceeds this by 20%.
- Match voltage to available service: 115V for 0.5–1HP shallow use; 230V single-phase for 1.5HP and above. Confirm your breaker and wire gauge (10 AWG for 230V runs over 100 ft).
- Require a 4-inch stainless body (304 minimum, 316 for corrosive water) and IP68 rating; check motor is oil-filled or water-cooled with thermal overload protection.
- Size cable and drop pipe to pump horsepower: 1.5HP needs 12–10 AWG submersible cable, 3HP needs 10–8 AWG; undersized wire causes voltage drop and motor burnout.
Specs
| Pump Type | Submersible deep-well vs jet shallow |
|---|---|
| Voltage / Phase | 115V or 230V, 60Hz single-phase |
| Head / Flow Range | 167–640 ft; 28–37 GPM |
| Body / Rating | 4-in stainless 304/316, IP68 |
Related searches
What to check before buying
- Measure well casing ID (must be at least 4 inches for a 4-inch submersible) and static water level with a drop line before ordering.
- Confirm electrical service at the wellhead: 115V or 230V, breaker amperage, and distance to panel to calculate wire gauge.
- Check pressure tank size and switch setting (typically 30/50 or 40/60 psi) so pump head rating covers the shutoff pressure plus lift.
- Verify water chemistry (sand, iron, hardness) to choose stainless grade and decide whether a torque arrestor or check valve is needed.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 20, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.