DIY Tool Picks

Dewalt Cordless Chop Saw Buying Guide

A DeWalt cordless chop saw is a battery-powered abrasive or carbide-tooth cut-off saw for framing, metal studs, and conduit, sold as either a 20V MAX brushed DCS373 or a 20V/60V FlexVolt brushless DCS690. The core trade-off is battery platform and blade technology: brushed 20V units cut light steel and rebar slowly, while FlexVolt brushless saws spin carbide blades fast enough for clean, burr-free cuts in steel and stainless. Buy the brushless FlexVolt DCS690 for daily metalwork; buy the 20V brushed DCS373 only for occasional rebar and angle-iron tasks.

Motor Type:Brushed 20V vs Brushless FlexVoltBlade & Arbor:14-in abrasive / 9-in carbide, 1-in arborBattery Platform:20V MAX vs 20V/60V FlexVoltMax Cut Capacity:5-1/8 in round at 90 degrees

At a glance

Price range
Price range not synced yet
Category
Power Tools
Data updated
Nov 20, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • DCS373 uses a 20V MAX brushed motor with a 14-inch abrasive wheel and cuts 5-1/8-inch round stock at 90 degrees.
  • DCS690 FlexVolt runs 20V/60V brushless power, uses a 9-inch carbide-tipped blade, and reaches 4,000 RPM for clean steel cuts.
  • FlexVolt batteries automatically switch between 20V and 60V, so one pack runs drills and the chop saw without a second charger.
  • Carbide-tooth blades cut steel with chips instead of abrasive dust, producing square ends that need no deburring on conduit.

Best use cases

  • Pick the DCS690 FlexVolt kit for daily steel stud, conduit, and strut cutting where clean square ends and speed matter more than battery weight.
  • Pick the DCS373 20V brushed saw for occasional rebar, angle iron, and fence-post work on sites already running 20V MAX packs.
  • Skip both for high-volume stainless or hardened alloy cutting where a corded 14-inch dry-cut saw delivers constant RPM and lower per-cut cost.
  • Skip the bare tool if you own only 12V MAX or 18V non-DeWalt packs; neither saw runs on those batteries without an adapter and correct-voltage pack.

Buying tips

  • Match the blade arbor: DCS373 takes 1-inch arbor 14-inch abrasive wheels; DCS690 takes a 1-inch arbor 9-inch carbide blade, so stock the right consumable before the tool arrives.
  • Buy a 60V FlexVolt 9.0Ah or larger pack for the DCS690; a 20V 5.0Ah pack in 60V mode delivers far fewer cuts per charge in steel.
  • For the DCS373, choose an abrasive wheel rated at or above the saw's no-load RPM and never exceed the wheel's marked maximum speed.
  • Budget for a chip-collection bag or vacuum adapter on carbide saws; dry-cutting steel throws hot chips and fines that abrasive saws do not.

Specs

Motor TypeBrushed 20V vs Brushless FlexVolt
Blade & Arbor14-in abrasive / 9-in carbide, 1-in arbor
Battery Platform20V MAX vs 20V/60V FlexVolt
Max Cut Capacity5-1/8 in round at 90 degrees

Related searches

What to check before buying

  • Measure the largest stock you cut: DCS373 clears 5-1/8-inch round at 90 degrees; DCS690 clears smaller stock but cuts steel far cleaner.
  • Confirm your battery platform: FlexVolt saws need 20V/60V FlexVolt packs or 20V MAX packs in 60V mode, not 12V MAX or 18V systems.
  • Check the work area for a stable bench or stand; both saws weigh several pounds with a battery and need a level surface for square cuts.
  • Verify the blade arbor and diameter match the saw; a 14-inch abrasive wheel will not fit the 9-inch DCS690 and voids the guard design.

FAQ

All Power Tools buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 20, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.