DIY Tool Picks

Photos from current listings. Actual item, color, and included accessories may vary.

Drill Bit Buying Guide

Drill bits are the cutting interface that determines whether a power tool performs or fails, with material grade and coating being the primary trade-off against cost. HSS bits handle wood and mild steel, cobalt or carbide grades are required for stainless and hardened metals, and masonry bits need carbide tips with flute geometry for impact. The decision rule is simple: match bit material and shank standard to the substrate and chuck type, or expect burned edges, snapped tips, and stripped shanks.

Bit Material:HSS / Cobalt (M35, M42) / CarbideShank Standard:1/4-in hex / Round / SDS-Plus / WeldonTip Geometry:Split point 135° / Brad point / Carbide masonrySubstrate Match:Wood / Metal / Masonry / Tile
Typical price range$57.99 – $379.99

At a glance

Category
Power Tools
Data updated
Nov 20, 2026

Current offers

Highlights

  • HSS (high-speed steel) bits cut wood, plastic, and mild steel up to roughly 30 HRC; cobalt (M35/M42) or solid carbide is mandatory for stainless steel and hardened alloys above 35 HRC.
  • Masonry bits use brazed carbide tips and are impact-rated only; they will shatter in a standard drill chuck if used on metal, and standard HSS bits will burn out in concrete.
  • Shank standards matter: 1/4-inch hex quick-connect fits impact drivers, 3/8-inch and 1/2-inch reduced shanks fit standard chucks, and SDS-Plus or SDS-Max slots are required for rotary hammers.
  • Annular cutters with Weldon shanks and diamond core bits with 5/8-11 thread are dedicated systems for mag drills and wet/dry coring, not interchangeable with hand-drill bits.

Best use cases

  • Best fit: for drilling mild steel and wood with a cordless drill, buy a 1/4-inch hex-shank HSS set with black oxide or titanium coating; skip cobalt unless you regularly drill stainless.
  • Best fit: for stainless steel, hardened bolts, or automotive frame work, use M35 cobalt split-point bits at low RPM with cutting fluid; skip standard HSS, which will dull and work-harden the surface.
  • Best fit: for concrete, brick, or block, use SDS-Plus carbide masonry bits in a rotary hammer; skip hex-shank masonry bits for anything larger than 3/8-inch, as they lack the impact energy transfer.
  • Wrong fit: never use a diamond core bit or annular cutter in a hand drill; these require a wet/dry coring rig or magnetic drill with the correct arbor and pilot pin.

Buying tips

  • Match shank to tool: 1/4-inch hex for impact drivers, round shank for 3/8-inch or 1/2-inch chucks, SDS-Plus for rotary hammers, and Weldon shank for mag drills.
  • For metal, choose split-point (135-degree) bits to prevent walking; for wood, brad-point or auger bits give cleaner holes; for masonry, carbide-tipped with flute depth at least 1.5x hole diameter.
  • Cobalt content matters: M35 (5% cobalt) handles stainless and cast iron; M42 (8% cobalt) suits harder alloys; solid carbide is for high-volume precision and is brittle under hand-drill side load.
  • Buy indexed sets with size markings and a metal index; cheap sets skip sizes and use soft steel that rounds at the shank under impact driver torque.

Specs

Bit MaterialHSS / Cobalt (M35, M42) / Carbide
Shank Standard1/4-in hex / Round / SDS-Plus / Weldon
Tip GeometrySplit point 135° / Brad point / Carbide masonry
Substrate MatchWood / Metal / Masonry / Tile

Related searches

What to check before buying

  • Confirm your drill chuck size and type (keyed, keyless, 1/4-inch hex, SDS-Plus) before buying any bit set; shank diameter must match the chuck's capacity.
  • Measure the required hole diameter and depth; bit length must exceed material thickness plus chuck clearance, and masonry bits need flute length longer than the anchor embedment.
  • Check substrate hardness: know whether you are drilling wood, mild steel, stainless, concrete, or tile, because bit material and tip geometry are not interchangeable across these.
  • Verify companion parts for specialty systems: mag drills need the correct arbor and pilot pin; core drills need a 5/8-11 threaded arbor and water feed for wet cutting.

FAQ

All Power Tools buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 20, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.