DIY Tool Picks

Milwaukee Hole Saw Kit Buying Guide

A Milwaukee hole saw kit is a collection of bimetal or carbide-tipped cup saws, arbors, and pilot bits designed for cutting large-diameter holes in wood, metal, and plastic with a handheld drill or drill press. The primary trade-off is tooth material and arbor design: bimetal (HSS teeth on a spring-steel body) handles nails and general-purpose cutting, while carbide-tipped saws cut faster in masonry, fiber cement, and stainless but cost more and chip on impact. The decision rule is simple: buy bimetal kits for mixed-material remodeling and carbide kits only for dedicated masonry or stainless work; avoid any kit that lacks a quick-change arbor and a pilot bit longer than the cup depth.

Tooth Material:Bimetal HSS vs Carbide-tippedArbor Shank:3/8 in hex / 7/16 in hex / 1/2 in roundMax Cup Diameter:1-1/4 in (3/8 arbor) to 6 in (7/16 arbor)Cutting Depth:1-5/8 in bimetal / 2 in carbide

At a glance

Price range
Price range not synced yet
Category
Power Tools
Data updated
Nov 20, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Bimetal construction (8% cobalt HSS teeth electron-beam welded to a shatter-resistant steel body) is the baseline for cutting wood with nails, drywall, and mild steel up to 1/8 in.
  • Carbide-tipped hole saws cut 3-5x faster in fiber cement, brick, and stainless steel but require a drill with a clutch or a drill press to avoid tooth fracture on breakthrough.
  • Arbor size determines maximum cup diameter: a 1/2 in shank arbor typically supports up to 1-1/4 in cups; 7/16 in hex shank arbors handle up to 2-1/8 in with a pilot drill long enough to clear the cup.
  • Milwaukee's Hole Dozer bimetal line uses a 4/6 variable-pitch tooth geometry and a 1-5/8 in cutting depth; carbide versions (e.g., Big Hawg) use 3 teeth per inch for aggressive masonry cuts.

Best use cases

  • Best fit: Bimetal kit (Hole Dozer) for remodelers cutting door latch bores, recessed light openings, and PVC pipe penetrations in wood-frame construction—skip carbide unless cutting masonry daily.
  • Best fit: Carbide-tipped kit for electricians and plumbers drilling repeated holes in brick, block, or fiber-cement siding where bimetal teeth dull after a few cuts.
  • Wrong fit: A 1/2 in chuck drill with a 2-1/8 in carbide cup in hammer mode—hammering fractures carbide teeth; use rotary-only mode or a drill press for cups over 1-1/2 in.
  • Wrong fit: Buying a kit with only 1-3/8 in to 2-1/8 in cups for door hardware—you need a 2-1/8 in cup for standard locksets and a 1 in or 1-3/8 in cup for deadbolts and conduit.

Buying tips

  • Match arbor shank to your drill: 3/8 in chuck drills need a 3/8 in hex shank arbor; 1/2 in chuck drills accept 7/16 in hex or 1/2 in round shank arbors for cups up to 6 in.
  • Pilot bit length must exceed cup depth by at least 1/4 in—standard pilot bits are 1/4 in diameter and 3-1/4 in long; short pilots cause the cup to bind before the center mark is drilled.
  • For metal over 1/8 in thick, choose bimetal with 6 teeth per inch (finer pitch) and use cutting fluid; coarse 4 TPI teeth grab and snap on thin sheet metal.
  • Kit cup count matters less than diameter spread: a 6-piece kit covering 3/4 in to 2-1/8 in handles most electrical and plumbing work; a 10+ piece kit adds 2-1/2 in to 4 in cups for HVAC and recessed lighting.

Specs

Tooth MaterialBimetal HSS vs Carbide-tipped
Arbor Shank3/8 in hex / 7/16 in hex / 1/2 in round
Max Cup Diameter1-1/4 in (3/8 arbor) to 6 in (7/16 arbor)
Cutting Depth1-5/8 in bimetal / 2 in carbide

Related searches

What to check before buying

  • Measure your drill chuck: 3/8 in chucks cannot grip 7/16 in hex arbors—confirm the arbor shank diameter matches your drill before buying a kit.
  • Verify the pilot drill is replaceable and uses a standard 1/4 in shank; proprietary pilot bits make the kit disposable when the tip dulls.
  • Check the case or organizer dimensions against your toolbag or van drawer—Milwaukee kits ship in either a blow-molded case or a soft bag; the hard case adds 1-2 in per side.
  • Confirm the kit includes a spare pilot bit and an arbor adapter (1/2 in to 5/8 in) if you plan to use a drill press with a 5/8 in chuck.

FAQ

All Power Tools buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 20, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.