DIY Tool Picks

Table Saw With Router Buying Guide

A table saw with router capability is a hybrid or accessory-driven setup that combines a 10-inch table saw with a router table, either via a shared cast-iron wing, a lift kit, or a dedicated combo unit. The core trade-off is between cast-iron flatness and motor independence versus the convenience of a single footprint; the decision rule is to buy a standard 10-inch contractor or cabinet saw with a proven aftermarket router-wing footprint rather than a proprietary combo that locks you into one vendor.

Saw Motor:1.75 HP (120V) vs 3-5 HP (220V)Router Power:2.25 HP fixed / 3.25 HP plungeWing Depth:27 in standard / 12 in widthLift Plate:8.25x11.75 in or 9.25x11.75 in

At a glance

Price range
Price range not synced yet
Category
Woodworking Saws & Planers
Data updated
Nov 20, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Router-wing compatibility hinges on bolt-pattern and table-flatness: cast-iron wings with pre-drilled 5/16-inch holes and 27-inch depth accept most standard router lifts and plates.
  • A 3 HP to 5 HP induction motor on the saw and a 1.75 HP to 3.25 HP router are the practical minimums for hardwood ripping and raised-panel routing without bogging.
  • Combo units with a shared motor (saw arbor driving router via belt) sacrifice router RPM consistency and typically cap at 1 HP equivalent, limiting them to softwood and light profiling.
  • Dado stack capacity of 13/16 inch and a riving knife that stays below the blade top are the two build metrics that most affect safe, accurate hybrid workflow.

Best use cases

  • Best fit: a home shop with 220V access and a 36-inch rip capacity should buy a 3 HP cabinet saw and add a cast-iron router wing with a 3.25 HP router lift for full cabinet and door production.
  • Best fit: a garage shop on 120V should pick a 1.75 HP contractor saw with a bolt-on router table extension and a 2.25 HP router; skip shared-motor combos that stall on 8/4 hardwood.
  • Wrong fit: a jobsite user needing portability should skip cast-iron router wings entirely; use a standalone trim-router table or a folding benchtop router station instead.
  • Wrong fit: a buyer expecting one switch to run both tools should avoid aftermarket wings; only integrated combo saws offer that, and they trade away router horsepower and lift precision.

Buying tips

  • Measure your saw's wing bolt pattern and table height before buying a router wing: standard contractor saws use a 27-inch deep, 12-inch wide wing with 5/16-inch bolts on 11-inch centers.
  • Match router lift to router body diameter: 3.5-inch (89 mm) and 4.2-inch (107 mm) are the two common sizes, and most lifts accept only one without an adapter.
  • Choose a saw with a riving knife and a T-square fence first; router capability is secondary, because a misaligned fence ruins both saw and router cuts.
  • For 220V cabinet saws, confirm a 20A dedicated circuit; for 120V contractor saws, a 15A circuit is the ceiling and shared-motor combos will trip it under load.

Specs

Saw Motor1.75 HP (120V) vs 3-5 HP (220V)
Router Power2.25 HP fixed / 3.25 HP plunge
Wing Depth27 in standard / 12 in width
Lift Plate8.25x11.75 in or 9.25x11.75 in

Related searches

What to check before buying

  • Measure the saw's cast-iron wing mounting holes center-to-center and the table height from the floor; the router wing must match both to sit flush.
  • Confirm the router lift plate opening matches your router's base diameter, and that the lift accepts the bit changes you need above the table.
  • Check shop voltage and breaker: 120V limits you to 1.75 HP saws and 2.25 HP routers; 220V is required for 3 HP and above.
  • Verify dust collection ports on both saw and router wing; a shared 4-inch port with a 2.5-inch router branch is the practical minimum for chip evacuation.

FAQ

All Woodworking Saws & Planers buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 20, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.