DIY Tool Picks

Cabinet Door Handle Template Buying Guide

A cabinet door handle template is a drilling jig that guarantees consistent, repeatable hole spacing for knobs and pulls across every door and drawer in a kitchen or bath project. The core trade-off is between stamped/slotted plastic guides with fixed spacings versus adjustable metal jigs with hardened bushings and true center-finding geometry. Buy an adjustable bushing jig if you are drilling more than a dozen doors or using mixed pull center-to-center sizes; settle for a fixed plastic template only for a single-size retrofit on a small batch.

Template Type:Fixed plastic vs adjustable metal jigCenter Spacing:3 in / 96 / 128 / 160 mmBushing Size:3/16 in (5 mm) or 1/4 in steelEdge Reference:Edge stop + stile centerline

At a glance

Price range
Price range not synced yet
Category
Woodworking Clamps, Jigs & Joinery
Data updated
Nov 20, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Fixed plastic templates lock one common center-to-center (typically 3 in / 76 mm or 96 mm) and cannot be re-set for other pull sizes.
  • Adjustable metal jigs use hardened steel drill bushings (commonly 3/16 in / 5 mm or 1/4 in) that prevent bit wander and wallow-out after repeated holes.
  • Self-centering and edge-reference stops reference off the door edge and stile centerline, so door width or hinge side no longer shifts hole position.
  • Bushing-guided jigs preserve hole diameter and verticality across dozens of doors; unsleeved plastic holes enlarge and skew after a few hundred plunges.

Best use cases

  • Full kitchen or vanity install with 15+ doors and drawers: pick an adjustable twin-bushing jig with edge stops so every pull lands at identical height and setback.
  • Single-size retrofit replacing existing 3 in or 96 mm pulls: a fixed plastic template matched exactly to that center-to-center is the fastest, lowest-error choice.
  • Mixed pull sizes or slab vs shaker doors: choose a jig with replaceable bushings and adjustable center spacing, and skip single-gauge templates entirely.
  • One-off cabinet or furniture build: a simple edge-and-center plastic guide is adequate; skip the premium machined jig unless you drill many doors.

Buying tips

  • Match the template's center-to-center exactly to the pull spec (3 in, 96 mm, 128 mm, etc.); a 3 in template cannot drill 96 mm holes without re-drilling.
  • Confirm bushing diameter matches your fastener or screw shank—most pulls use #8 screws, requiring roughly 3/16 in / 5 mm clearance holes.
  • Check that the jig references the door edge and stile centerline simultaneously; edge-only jigs drift on doors with inconsistent stile widths.
  • Prefer hardened steel bushings over bare plastic holes if you will drill more than a few dozen doors, since plastic wears and enlarges the guide.

Specs

Template TypeFixed plastic vs adjustable metal jig
Center Spacing3 in / 96 / 128 / 160 mm
Bushing Size3/16 in (5 mm) or 1/4 in steel
Edge ReferenceEdge stop + stile centerline

Related searches

What to check before buying

  • Measure your pull's center-to-center distance and screw diameter before choosing a template gauge or bushing set.
  • Confirm door thickness and edge profile fit the jig's clamp or stop depth, especially on thick or beveled shaker doors.
  • Verify the template references the hinge-side or opening edge your installation layout uses so handle height stays consistent.
  • Check your drill bit shank fits the jig bushing and that the bit is the correct clearance size for the pull screws.

FAQ

All Woodworking Clamps, Jigs & Joinery buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 20, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.